rc

Description

PARTS LIST Motors - 2830-8 1300KV Outrunner Brushless Motor Free Mounts http://www.rctimer.com/index.php?gOo=goods_details.dwt&goodsid=120&productname= Speed controller - hobby king Hobbyking SS Series 18-20A ESC (card programmable) http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=6548 Or a little better controller is the Exceed RC Proton 30A Brushless ESC Speed Controller at hobby partz http://www.hobbypartz.com/proton30aair.html or plush 30 amp at hobbyking http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=2164 Controller at hobbyking HobbyKing Multi-Rotor Control Board V2.1 (Atmega168PA) http://www.hobbyking.com/hobbyking/store/__19534__HobbyKing_Multi_Rotor_Control_Board_V2_1_Atmega168PA_.html or the new KKv2 board no need for a programmer or computer. http://www.hobbyking.com/hobbyking/store/__24723__Hobbyking_KK2_0_Multi_rotor_LCD_Flight_Control_Board.html Programmer at hobby king USBasp AVR Programming Device for ATMEL processors http://www.hobbyking.com/hobbyking/store/__21321__USBasp_AVR_Programming_Device_for_ATMEL_proccessors.html 10CM Male to Male Servo Lead (JR) 26AWG (10pcs/set) http://www.hobbyking.com/hobbyking/store/__21758__10CM_Male_to_Male_Servo_Lead_JR_26AWG_10pcs_set_.html I use 14 gauge wires http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=9678 red http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=9679 black 1/2 inch wood from home depot or Lowes found in the trim area 1/8 inch ply from craft store or hobby shop 4-40x 1 screws blind nuts and washers from Trimcraft Aviation http://www.trimcraftaviationrc.com/index.php?main_page=product_info&cPath=4_17&products_id=43 screw http://www.trimcraftaviationrc.com/index.php?main_page=product_info&cPath=59_9_29&products_id=96 washers http://www.trimcraftaviationrc.com/index.php?main_page=product_info&cPath=42&products_id=205 blind nuts Zip ties, Velcro and some paint i also found a piece of ½ x1 ½ x 2 or 3 foot hard wood at home depot I use for the rear pivot I cut into a 1 1/2 x 1 1/2 square. I have purchased a used drill press so no more crooked stuff. Props can be had at hobby king if hobby parts is out http://www.hobbypartz.com/8x4.html Hobbypartz http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=11331 hobbyking I now use a 4MM carbon fiber rod instead of the screw with a wheel collar for the rear pivot. Just drill a hole in the back of the rear arm about an inch deep and glue it in there. link to template. you will have to enlarge it to build my tri. http://rcexplorer.se/page24/files/Tricoptertemplate.pdf low voltage beeper http://www.hobbyking.com/hobbyking/store/__7223__Hobby_King_Battery_Monitor_3S.html louder low voltage beeper you connect to ballance taps http://www.hobbyking.com/hobbyking/store/__18987__On_Board_Lipoly_Low_Voltage_Alarm_2s_4s_.html